AMC/AMSC: 1G
1 Suitable for competitive acquisition. (See Notes 1 and 2)
G The Government has unlimited rights to the technical rights to the technical data, and the data package is complete. Valid AMCs: 1 and 2.
Drawings –
ITEM NAME: CIRCUIT CARD ASSEMBLY
RP001: DLA PACKAGING REQUIREMENTS FOR PROCUREMENT
RD002, COVERED DEFENSE INFORMATION APPLIES
RA001: THIS DOCUMENT INCORPORATES TECHNICAL AND/OR QUALITY REQUIREMENTS
(IDENTIFIED BY AN 'R' OR AN 'I' NUMBER) SET FORTH IN FULL TEXT IN THE
DLA MASTER LIST OF TECHNICAL AND QUALITY REQUIREMENTS FOUND ON THE WEB
AT:
http://www.dla.mil/HQ/Acquisition/Offers/eProcurement.aspx
FOR SIMPLIFIED ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE
SOLICITATION ISSUE DATE OR THE AWARD DATE CONTROLS. FOR LARGE
ACQUISITIONS, THE REVISION OF THE MASTER IN EFFECT ON THE RFP ISSUE DATE
APPLIES UNLESS A SOLICITATION AMENDMENT INCORPORATES A FOLLOW-ON
REVISION, IN WHICH CASE THE AMENDMENT DATE CONTROLS.
RQ009: INSPECTION AND ACCEPTANCE AT ORIGIN
RQ011: REMOVAL OF GOVERNMENT IDENTIFICATION FROM NON-ACCEPTED SUPPLIES
RQ032: EXPORT CONTROL OF TECHNICAL DATA
This item has technical data some or all of which is subject to
export-control of either the International Traffic in Arms regulations
(ITAR) or the Export Administration Regulations (EAR), and cannot be
exported without prior authorization from either the Department of State
or the Department of Commerce. Export includes disclosure of technical
data to foreign persons and nationals whether located in the United
States or abroad. This requirement applies equally to foreign national
employees and U.S. companies and their foreign subsidiaries. DFARS
252.225-7048 is applicable to this data.
The Defense Logistics Agency (DLA) limits distribution of export-control
technical data to DLA contractors that have an approved US/Canada Joint
Certification Program (JCP) certification, have completed the
Introduction to Proper Handling of DOD Export-Controlled Technical Data
Training and the DLA Export-Controlled Technical Data Questionnaire
(both are available at the web address given below), and have been
approved by the DLA controlling authority to access the
export-controlled data. Instructions for obtaining access to the
export-controlled data can be found at:
https://www.dla.mil/Logistics-Operations/Enhanced-Validation/
To be eligible for award, offerors and any sources of supply proposed
for use are required to have an approved JCP certification and have
been approved by the DLA controlling authority to access
export-controlled data managed by DLA. DLA will not delay award in
order for an offeror or its supplier to apply for and receive approval
by the DLA controlling authority to access the export-controlled data.
RQ039: Non-Tailored Higher-Level Quality Requirements (SAE AS9100) for
Manufacturers and Non-Manufacturers
RT001: MEASURING AND TEST EQUIPMENT
PART NAME ASSIGNED BY CONTROLLING AGENCY: CIRCUIT CARD ASSEMBLY, PHASE
SHIFTER DRIVER ELECTRO-STATIC SENSITIVE DEVICE
MIL-STD-130N(1) DATED 16 NOV 2012.
IDENTIFICATION MARKING OF U.S. MILITARY PROPERTY
MERCURY OR MERCURY CONTAINING COMPOUNDS SHALL
NOT BE INTENTIONALLY ADDED TO<(>,<)> OR COME IN DIRECT
CONTACT WITH<(>,<)> ANY HARDWARE OR SUPPLIES FURNISHED
UNDER THIS CONTRACT. EXCEPTION: FUNCTIONAL MERCURY
USED IN BATTERIES, FLUORESCENT LIGHTS, REQUIRED
INSTRUMENTS; SENSORS OR CONTROLS; WEAPON SYSTEMS;
AND CHEMICAL ANALYSIS REAGENTS SPECIFIED BY NAVSEA.
PORTABLE FLUORESCENT LAMPS AND PORTABLE INSTRUMENTS
CONTAINING MERCURY SHALL BE SHOCK PROOF AND CONTAIN
A SECOND BOUNDARY OF CONTAINMENT OF THE MERCURY OR
MERCURY COMPOUND. (IAW NAVSEA 5100-003D).
REFERENCE CONTROL PART NUMBER 7624570 CAGE 53711
SAMPLING:
THE SAMPLING METHOD SHALL BE IN ACCORDANCE WITH MIL-STD-1916 OR ASQ
H1331, TABLE 1 OR A COMPARABLE ZERO BASED SAMPLING PLAN UNLESS OTHERWISE
SPECIFIED BY THE CONTRACT. IF THE APPLICABLE DRAWING, SPECIFICATION,
STANDARD, OR QUALITY ASSURANCE PROVISION (QAP) SPECIFIES CRITICAL, MAJOR
AND/OR MINOR ATTRIBUTES, THEY SHALL BE ASSIGNED VERIFICAITON LEVELS OF
VII, IV AND II OR AQLS OF 0.1, 1.0 AND 4.0 RESPECTIVELY. UNSPECIFIED
ATTRIBUTES SHALL BE CONSIDERED AS MAJOR UNLESS SAMPLING PLANS ARE
SPECIFIED IN APPLICABLE DOCUMENTS. FOR MIL-STD-1916, THE MANUFACTURER
MAY USE THE ATTRIBUTE OR VARIABLE INSPECTION METHOD AT THEIR OPTION OR
PER THE CONTRACT. MIL-STD-105/ASQ Z1.4 MAY BE USED TO SET SAMPLE LOT
SIZE, BUT ACCEPTANCE WOULD BE ZERO NON-CONFORMANCES IN THE SAMPLE LOT
UNLESS OTHERWISE SPECIFIED IN THE CONTRACT.
OVERALL LENGTH: 5.740 INCHES NOMINAL OVERALL WIDTH: 1.619 INCHES NOMINAL
MAJOR COMPONENTS: CONNECTOR ASSY, ELECTRICAL (7624566-2/53711) 1;
PRINTED WIRING BOARD, PHASE SHIFTER DRIVER, 1; NO KEYING PINS SPECIAL
FEATURES: NO KEYING PIN; MODEL WITH KEYING PIN IS 7624570-1. END ITEM
IDENTIFICATION: AS-4108/SPY PHASED ARRAY ANTENNA
CRITICAL APPLICATION ITEM
IAW BASIC DRAWING NR 53711 7624570
REVISION NR D DTD 06/21/2011
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624570
REVISION NR F DTD 02/06/2009
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 10001 2900594
REVISION NR AE DTD 12/01/2014
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 10001 3256939
REVISION NR P DTD 02/28/2013
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624560
REVISION NR A DTD 06/19/2013
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624561
REVISION NR B DTD 01/30/2018
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624562
REVISION NR C DTD 05/08/2019
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624563
REVISION NR L DTD 03/10/2017
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624565
REVISION NR DTD 09/22/2005
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624566
REVISION NR G DTD 02/21/2020
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624567
REVISION NR A DTD 01/15/2007
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624569
REVISION NR C DTD 08/19/2009
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624573
REVISION NR D DTD 10/17/2023
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624574
REVISION NR B DTD 09/07/2011
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624575
REVISION NR C DTD 06/25/2020
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624576
REVISION NR D DTD 11/07/2018
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624578
REVISION NR A DTD 05/15/2013
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624581
REVISION NR DTD 05/13/2004
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624583
REVISION NR A DTD 07/11/2016
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624590
REVISION NR A DTD 02/13/2018
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624591
REVISION NR B DTD 05/23/2017
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624592
REVISION NR A DTD 06/30/2008
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624593
REVISION NR C DTD 05/10/2018
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624596
REVISION NR B DTD 06/28/2013
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624597
REVISION NR A DTD 06/13/2006
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624598
REVISION NR C DTD 05/14/2020
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624599
REVISION NR B DTD 09/07/2011
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624600
REVISION NR C DTD 01/10/2018
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624602
REVISION NR C DTD 01/10/2013
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624603
REVISION NR C DTD 07/01/2010
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624604
REVISION NR A DTD 01/10/2013
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 7624605
REVISION NR DTD 09/22/2005
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 53711 8306492
REVISION NR B DTD 08/21/2020
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 10001 WS10288
REVISION NR AB DTD 04/05/2001
PART PIECE NUMBER:
IAW REFERENCE DRAWING NR 10001 WS10298
REVISION NR DTD 06/29/1983
PART PIECE NUMBER:
Please review the NSN listed above and provide any sources that may be able to manufacture these items. The approved sources for this NSN are currently listed above. All information may be submitted directly to the Contract Specialist listed above. This information must be provided by the response date indicated above.
In order to be considered an interested party, vendors must complete and return the attached Market Survey to the Contract Specialist listed above by the required response date.
NOTE: This project contains Drawings/Specifications. You may access the TDP directly from cFolders and searching for the above cited Solicitation Number.
You may access them only through the following link: https://pcf1.bsm.dla.mil/cfolders.
The drawings cannot be accessed through DIBBS.
Thank you in advance for your assistance.
