The Defense Logistics Agency (DLA) Maritime Norfolk at Norfolk Naval Shipyard (NNSY) intends to award a Firm Fixed Price (FFP) Single Award Contract with Lowest Price Technically Acceptable (LPTA) Evaluation Factors for the item listed below. The required item is for commercial items prepared in accordance with the information in FAR Part 13 and FAR Subpart 12.6, as supplemented with the additional information included in this notice.
The Contract Line Items (CLINs) is as follows:
CLIN 0001 QTY 15
SYNCHRO, CONTROL TRANSFORMER
NOTE: Programming stations are stand alone and are not connected to any networks.
ORDERING DATA
Description:
Control Transformer Synchro
Body Material:
Steel, stainless
AAQL
Body Style:
Standard round c AAVH
Shoulder Diameter:
Between 1.5615 inches and 1.5620 inches AAVL
Pilot Diameter:
Between 0.9370 inches and 0.9375 inches ABHP
Overall Length:
3.0600 inches ABKK
Flange Diameter:
Between 1.7450 inches and 1.7500 inches ABKU
Flange Thickness:
0.0930 inches ABPA
Undercut Diameter:
1.6250 inches ABPC
Undercut Width:
0.0780 inches ABWV
Shaft Diameter:
0.1870 inches single shaft and 0.1872 inches single shaft ABXF
Shaft Length:
0.5400 inches single shaft AHCG
Maximum Tempurature Rise:
20.0 degrees Celsius
AJSL
Body Size:
18
AJSN
Stator Input Voltage Rating In Volts:
90.0
AJSP
Stator Input Current Rating:
7.0 milliamperes AJSQ
Stator Input Electrical Power Rating:
50.0 milliwatts AJSS
Frequency In Hertz:
400.0
AJTJ
Zso Impedance Magnitude In Ohms:
Between 12000.00 and 14800.00 AJTK
Zso Impedance Angle In Deg:
Between 82.00 and 84.50 AJTL
Zrs Impedance Magnitude In Ohms:
Between 980.00 and 1180.00 AJTM
Zrs Impedance Angle In Deg:
Between 42.00 and 52.00 AJVF
Phase Shift Angle In Deg:
2.000 input to output AJVG
Maximum Fundamental Null Voltage In Millivolts Per Volt
20.00 output AJVH
Maximum Total Null Voltage Output In Millivolts Per Volt 30.00
AJVL
Electrical Error Angular Range In Minutes:
-6.0/+6.0
AJVM
Spline Tooth Quantity:
21 single shaft AJW
Torque Gradient Per Angular Deg:
0.100 inch-ounces AJVW
Alignment Hole Quantity:
4
AJWQ
Pilot Length:
0.0400 inches AJWR
Shoulder Length:
0.1320 inches AJWX
Mounting Surface To Terminal End Distance:
2.5200 inches AJXA
Spline Tooth Diametral Pitch:
120 single shaft AJYY
Shaft Thread Series Designator:
Unf single shaft AKAF
Shaft Thread Direction: Right-hand single shaft AKAN
Shaft Thread Class:
2a CQTM
Terminal Location:
Rear CQWQ
Shaft Thread Length:
0.2000 inches single shaft CRSJ
Shaft Type:
Spline w/threads single shaft
CRSY
Alignment Hole Depth:
0.1250 inches CSJY
Transformation Ratio:
0.735 rotor to stator CTCW
Alignment Hole Bolt Circle Diameter:
1.2500 inches CWBH
Shaft Thread Size:
0.190 inches single shaft TEST
Test Data Document:
81349-mil-s-20708 specification (includes engineering type bulletins, brochures, etc., that reflect specification type data in specification format; excludes commercial catalogs, industry directories, and similar trade publications, reflecting general type data on certain environmental and performance requirements and test conditions that are shown as "typical", "average", "", etc.).
TTQY
Terminal Type And Quantity: 5 screw
FACILITIES ENTRY REQUIREMENTS:
Initial Entry: Contractor provide a SECNAV 5512 and a CNRMA Installation Access Screening Request form that will be provided by the technical point of contact (TPCO). These documents will be endorsed by the TPOC and forwarded to the NNSY Pass Oice Contractor shall submit documents approximately two weeks before arrival.
· Vehicle Entry: The company name shall be displayed on each door of the Contractor’s vehicles in a manner and size that is clearly visible. All vehicles shall display a valid state license plate that complies with State Vehicle Code. Vehicles shall meet all other requirement of the State Vehicle Code, such as safety standards, and shall carry proof of insurance and state registration. Passes will be issued for vehicles to enter the shipyard. A separate pass is required for entering the Controlled Industrial Area (CIA).
Portable Electronic Device (PED): In accordance with COMSUBLANT/COMSUBPACINST 2075.1C, the use of Portable Electronic Devices (PEDs) while in or on Department of Navy Controlled, Industrial Areas are prohibited. A portable electronic device (PED) is defined as any non-stationary electronic apparatus with singular or multiple capabilities of, but not limited to recording, storing, and/or transmitting data, voice, video, or photo images e.g.: cell phones, laptops, tablets and wearable devices such as fitness bands and smart watches.
Critical time Constraints: The Installation and training shall be performed between the
hours of 7:20 am and 3:50 pm excluding any federal holidays. · Safety: “Per FAR 22.102-1(a) entitled “Safety”, contractor are hereby informed that their employees or representatives present on property under NNSY cognizance must follow Federal and State OSHA requirements; NNSY OSHE Program Manual, NAVSHIPYDNORINST P5090.2 requirements; OSHE Control Manual (OSHECM) requirements; or safety requirements for site specific location of the contract."
Location: Portsmouth, VA 23709 The requirement will be solicited as a total small business set aside. The NAICS code applicable to this procurement is 335312, Electrical/electronic Eqpt Compnts, Synchros and Resolvers with a size standard of 500 employees. The Product Service Code is 5990.
The anticipated delivery date for this acquisition is 30 days ARO. The solicitation, any documents related to this procurement, and all amendments issued will be in electronic form only. The solicitation number is SPMYM125Q0010 and it is expected to be available on or about 7 November 2024 and posted to SAM.gov, https://sam.gov/ Quotes will be due by 4:00 PM EST on 14 November 2024. Responses to the solicitation notice shall be emailed to the attention of John Ratliff as john.ratliff@dla.mil. Please make sure that the solicitation number (SPMYM125Q0010) is included in the subject line of any email correspondence. Emails without subject lines will not be read because of security issues.
Potential offerors are hereby notified that the solicitation and any subsequent amendments will only be available by downloading the documents at www.SAM.gov (Contracting Opportunities). The Government is not responsible for inability of the Offeror's to access solicitation documents posted. Prospective Offeror's should also register at on the interested vendor list under SPMYM125Q0010. No telephone or FAX requests will be accepted, and no hardcopy solicitation/amendment will be mailed or faxed.
All responsible sources may submit a proposal which may be considered by the Government. By submitting a quote, the offeror will be self-certifying that neither the principal corporate officials nor owners are currently suspended, debarred, or otherwise ineligible to receive contracts from any federal agency. Failure to do so may represent grounds for refusing to accept the proposal. By submission of a proposal, the offeror acknowledges the requirement that a prospective awardee must be registered in the System for Award Management (SAM) database prior to award, during performance, and through final payment of any contract resulting from the solicitation, except for awards to foreign vendors for work to be performed outside the United States. Lack of registration in the SAM database will make an offeror ineligible for award. Offerors may obtain information on registration and annual confirmation requirements by calling 1-866-606-8220, or via the Internet at https://www.sam.gov. All questions shall be submitted in accordance with the solicitation, dates and procedures. Please direct all questions regarding this requirement to John Ratliff at john.ratliff@dla.mil.
