Specifications include, but are not limited to: Dump Body: Mounted & fully operational. One year warranty. 18ft. Asphalt type box, AR400 steel construction, Uni-body design, preferred. Dump body to be primed and painted gray with Utech 2000 Acrylic Urethane Finish. AR400 steel dump body / Understructure & top of floor to be painted black. 96” outside width & 84” inside width (20 cu. yard capacity minimum), 3/16” AR400 steel sides & ends. 60in. high header with one piece, 3/16”. AR400 steel sloped sides from 60” header to 52” tailgate. 1/4” AR400 steel air trip tailgate. 52in. tailgate height. Single panel, air trip tailgate, air over air. Install tailgate grab handles, one in each lower corner & install D-ring on top inside of Tailgate. Also tailgate chains for spreading. One-piece ¼” AR400 floor with rounded floor to side radius, 200,000 PSI tensile strength. Under frame is two 8” structural steel I-beam long sills fully welded to prevent internal rusting, with “No splices”. Bottom rub rails and top rails are sloped for dirt & debris shedding, 10ga, grade 50 steel. Fully boxed-in & fully welded top rails, 10ga, grade 50 steel. Contoured front corner post, 10ga, grade 50 steel. Full depth rear corner post, 7ga, 409 stainless-steel. Steel 5 rung ladder mounted on rear driver’s side. Full width cab shield, 10-gauge, grade 50 steel, with 7-gauge end plates. Back-up alarm / Body-Up light switch wired to Ultra-6100 display. One set of shovel hooks, mounted to County spec TBD. (Steel round stock). Two sets of mud flaps, rear set quick detachable type, behind drive wheels and one set in front of pusher axle. Vibrator: Cougar Vibrator, Model 3200, installed with additional custom plate, preferred. Tarp: Donovan Electric tarp system with side mount springs, heavy duty asphalt tarp, all aluminum arms & tarp housing, preferred. Trailer Hitch: 1” Rear Pintle Plate with heavy duty gussets and 35 Ton minimum pintle hitch with D-rings. 7 pin spade and 7 pin RV type trailer plug, installed and wired for stop, turn and taillights. Airlines should be added and capped off (air lines must be mounted to the extreme outside). Plate must also be drilled for a chipper bar and have chipper bar made for it. Lighting: Three (3) oval light holes in each rear corner post (for F/S LED S/T/T, LED Back-Up, and LED amber warning Lights). Two (2) std. LED marker lights installed on both outer sides of rear corner post. LED 3-light cluster mounted on rear hitch plate. All electrical wiring connections will be put in heat shrink tubing & will run to a sealed junction box. Dump box electrical wiring will be run using 7/14 trailer wire to a 7 pole, spade type, round plug located on the passenger’s side back of the cab. The trailer wire will be secured along the frame with the use of properly sized tubing clamps, with a maximum of 12” spacing. 3M reflective red/silver conspicuity tape is to be installed on both sides of the dump body, along the rub rail per DOT specs. 3M reflective red/silver conspicuity tape to outline the tailgate. Side mounted strobe on dump body towards the rear (may be integrated with rear facing lights) Body Hoist: Mailhot Hoist telescopic (Capacity is 26.3 ton). Single acting, power up/gravity down. Trunnion mounted nitrided cylinder. “No” cylinder doghouse: Cylinder is externally mounted in a full-length cradle (for oil tank & valve body). Oil tank to be cradle mounted on passenger side between the front of the box and back of the cab. Valve body w/enclosure to be cradle mounted on the driver’s side between the front of the box & back of cab. Rear hinge pins to be 303 stainless steel and rifle drilled with grease zerks. Garlock type hinge pin bushings. Proximity switch- used as hoist limiter. Two (2) safety body props. Two-year factory warranty Spreader: This specification shall describe a slide-in combination V-box material spreader with integrated poly liquid tanks, anti-ice direct liquid sprayer, and a pre-wet system or approved equal. Unit must be capable of hauling and spreading free flowing granular materials, anti-ice liquid application, and a pre-wet liquid onto granular material. This unit shall consist of a 304 stainless steel body with integral high-capacity liquid reservoir and a V-box dual auger drive conveyor system, rear discharge conveyor, spinner disc, power drive, liquid pre-wet pump, high-capacity anti-ice liquid pump and all components necessary to make a complete operating unit. Overall unit length to be approximately 196”. V-box hopper length to be 16’ minimum. Body granular hopper capacity shall be a minimum of (8.3) yd3 struck. Body liquid capacity shall be a minimum of 1,728 US Gallons The outside body widths shall be 82”. The inside width of the v-box shall be 72”. Unit shall be constructed from no less than 304 grade stainless steel unless specified otherwise herein. Approximate weight shall be 5900lbs empty. Unit shall be designed for use as a slip into a dump body installation. Unit shall include a fully enclosed rear cabinet which shall contain all the liquid pumps, liquid valves, flow meter, and hydraulic valves. Hydraulic valves to be supplied by hydraulic supplier.
